Purpose of the development: Коалесцентный отделитель нефтепродуктов предназначен для отделения нефтепродуктов плотностью до 0, 95 г/см3, таких как бензин, kerosene, diesel fuel and automotive or industrial oil.

Recommended application field: Сфера использования нефтеотделителей - это очистка дождевых стоков или других стоков, содержащих нефтепродукты, на parking lots, gas stations, car washes, service stations, storage tanks, etc.

Technical characteristic: Types of oil separators Depending on the location and purpose can be made several types of oil separators: "Oil separators with bypass piping "For penetration into the ground to add: "> Travel "> Does not travel "For the location of the surface n Max. water flow l / s Length (mm) Width (mm) Height (mm) height of the input. Tp. (mm) height of the new. Tp. (mm) NP-2 2 2000 1030 2080 1680 1480 NPP-2 2 2400 1030 2080 1680 1380 SPE-4 4 2160 2000 2000 1600 1150 SPE-5 5 4160 2000 2000 1600 1150 SPE-8 8 5160 2000 2000 2000 1500 SPE-15 15 6160 3000 3000 2500 2000

Advantages over analogues: Advantages of oil separators: high separation efficiency -99.5% use of materials resistant to corrosion. simplicity of design, installation, maintenance and operation. no moving parts. does not require energy. does not require consumables. lifetime - more than 25 years. lifetime warranty - 2 years. Quality indicators for cleaning up: in the coalescent oil separator effluent is allowed to sum up the content of petroleum products up to 1000 mg / l. When using the coalescent oil separators with one degree of purification of the oil content in the effluent after treatment is not more than 5 mg / l. When using the coalescent oil separators with sorption filter, the oil content in the effluent after treatment is not more than 0.34 mg / l. When using the coalescent oil separators with enhanced sorption filter, the oil content in the effluent after treatment is not more than 0.2 mg / l.

The development stage readiness: Introduced in production

Description of the development:
()
Oil separators is a reservoir of rectangular or cylindrical form made of polypropylene. Body oil separators 100% waterproof. Inside the hull installation of interior partitions divided into 3 functional parts. At the top of the hatches are designed to control the robot oil separators for the oily waste sampling and heavy parts. To control the level of purification, if desired, can be installed alarm system. Oil separators are made of polypropylene plates 15 mm thick. At a high level of ground water wall installation strengthened to prevent ejection. Mounted on concrete base thickness of 15-20cm. The purification technology: contaminated water through the inlet pipe enters the first compartment of oil separators, which decreases the flow of forces and gravitational separation of heavy particles (sand, small stones, etc.) as well as a partial segmentation of petroleum products. These particles settle to the bottom compartment as well as heavier than water. The water then goes through a submerged wall to the second compartment, where the main water treatment. The density of petroleum products is less than the density of water, so oil accumulates on the surface. Out and collected by special devices or equipment. These wastes must be disposed of specialized. The second compartment is mechanically purified water passes through the submerged barrier in the third compartment. In the third compartment by means of adsorbing material is post-treatment water. The accumulated oil removed from the installation of the following ways: - Manually - Submersible pump, - Overflow into the collecting tank through the collector of petroleum products. This compartment can be installed one or more of the sorption filter depending on the level of water purification. Filters are made mostly of sorption material FIBROLL. Sorption capacity of such a filter is about 3-5 grams of oil per gram of textile FIBROLL. Modern oil separators, which serve large areas (parking lots, parking lots, gas stations, etc.) have some structural features. To clean the waste water from oil with a sharp increase in wastewater (eg, rain) in their design the bypass conduit. With a sharp increase in revenues, most oil-containing waste water particles in the oil separators will go directly to the first incoming wastewater. Further water does not contain mineral oil or contains very little. Therefore, the basic amount of water will pass through the bypass line, the capacity which is 4-5 times higher than that of the oil separators.

Possibility of transfer abroad:
Licence's sale
Realization of finished commodity

Photo

Country Ukraine

For additional information turn to:
E-mail: gal@uintei.kiev.ua